Diesel Tools

MANUAL SLEEVE PULLER SET - Sleeve Puller/Installer Sets: These sets work on a wide array of truck, bus, and tractor engines, as well as those in ot...

CUMMINS ENGINE BARRING TOOL - Need to manually rotate an engine? This tool makes the job easy. Just insert the tool into the flywheel housing until...

ENGINE BARRING SOCKET - Designed to rotate engine on a Mack E7 and Cat 3208. Similar to J-38587-A.

This socket adapter is used to remove and install injector feed tubes on select Detroit Diesel engines. The unique design provides proper clearance...

This fuel system coupler fitting connects to a "compu-check" quick-connect fitting. Applications include Detroit Diesel S60, MBE900, and MBE4000. S...

INJECTOR HEIGHT GAUGE, 1.460-INCH - This mechanical gauge is used to set injector height to 1.460" (37.08 mm). For use on Detroit Diesel Two cycle ...

Designed to work with set Nos. 1200, 1202, and 1203, these removal plates fit the full spectrum of cylinder sleeve sizes. Determine engine bore siz...

This tools is used to properly align the cam gear during camshaft assembly installation. The pin on the tool fits into the cam timing hole for prop...

This deep-well 12mm socket is used to torque the rocker arm nut to OE specification and has a stepped outside diameter for proper clearance and acc...

FORD FUEL LINE DISCONNECT TOOL FOR 6.0L - Use to disconnect the high-pressure oil rail supply line from the fuel rail when removing fuel injectors....

DAVCO DIESEL FILTER WRENCH - Found on Caterpillar, Cummins, Detroit Diesel, International, Mack, Mercedes-Benz, Volvo and other engines - Fits Davc...

DAVCO DIESEL FILTER WRENCH - Davco Diesel Filter Wrench - Found on Caterpillar, Cummins, Detroit Diesel, International, Mack, Mercedes-Benz, Volvo ...

GM DURAMAX INJECTOR PULLER - Designed to pull injectors on a GM Duramax 6.6L engine, 2005 - 2011 - Similar to J-46594.

CUMMINS ENGINE BARRING TOOL - Need to manually rotate an engine? This tool makes the job easy. Just insert the tool into the flywheel housing until...

DAVCO DIESEL FILTER WRENCH - Davco Diesel Filter Wrench - Found on Caterpillar, Cummins, Detroit Diesel, International, Mack, Mercedes-Benz, Volvo ...

DAVCO DIESEL FILTER WRENCH - Found on Caterpillar, Cummins, Detroit Diesel, International, Mack, Mercedes-Benz, Volvo and other engines - Fits Davc...

This deep-well 12mm socket is used to torque the rocker arm nut to OE specification and has a stepped outside diameter for proper clearance and acc...

This mechanical gauge is used to set injector height to 3.232" (82.09 mm). For use on Detroit Diesel Series 60 engines. Similar to J-45002.

DIESEL COMPRESSION TESTER WITH ADAPTERS - Easy-to-use compression tester is designed specifically for medium-duty diesel engines equipped with glow...

UNIVERSAL PULLER FOR WET-TYPE SLEEVES - This tool will remove cylinder sleeves faster than ordinary pullers because it requires very little setup t...

This adapter allows for proper engine pre-lubing, preventing dry starts after engine service. The adapter installs into the oil priming port in the...

GM DURAMAX INJECTOR PULLER - Designed to pull injectors on a GM Duramax 6.6L engine, 2005 - 2011 - Similar to J-46594.

FUEL SYSTEM PRIMING PUMP - Pressurizing the fuel system after service is essential for proper fuel system operation and efficient starting. This ta...

OTC DEF REFRACTOMETER - EPA regulations require all diesel engines manufactured on or after January 1, 2010 to meet lowered NOx emissions standards...

Designed to work with set Nos. 1200, 1202, and 1203, these removal plates fit the full spectrum of cylinder sleeve sizes. Determine engine bore siz...

INJECTOR HEIGHT GAUGE, 1.460-INCH - This mechanical gauge is used to set injector height to 1.460" (37.08 mm). For use on Detroit Diesel Two cycle ...

This mechanical gauge is used to set injector height to 3.232" (82.09 mm). For use on Detroit Diesel Series 60 engines. Similar to J-45002.

DIESEL COMPRESSION TESTER WITH ADAPTERS - Easy-to-use compression tester is designed specifically for medium-duty diesel engines equipped with glow...

MANUAL SLEEVE PULLER SET - Sleeve Puller/Installer Sets: These sets work on a wide array of truck, bus, and tractor engines, as well as those in ot...

This socket adapter is used to remove and install injector feed tubes on select Detroit Diesel engines. The unique design provides proper clearance...

FUEL SYSTEM PRIMING PUMP - Pressurizing the fuel system after service is essential for proper fuel system operation and efficient starting. This ta...

ENGINE BARRING SOCKET - Designed to rotate engine on a Mack E7 and Cat 3208. Similar to J-38587-A.

This fuel system coupler fitting connects to a "compu-check" quick-connect fitting. Applications include Detroit Diesel S60, MBE900, and MBE4000. S...

FORD FUEL LINE DISCONNECT TOOL FOR 6.0L - Use to disconnect the high-pressure oil rail supply line from the fuel rail when removing fuel injectors....

This tools is used to properly align the cam gear during camshaft assembly installation. The pin on the tool fits into the cam timing hole for prop...