Specialty Service Tools

REAR CUP BEARING REPLACER

OTC Bosch 1699501320 BAT 120 Battery and Starter/Charger System Tester for use with Bosch ADS 325/ADS 625 Encore/Evolve Diagnostic Tools. The BAT 1...

For Reinstalling the Manifold on Small Block Chevrolets. A simple way to expand a warped manifold so all bolt holes are accurately aligned. Helps p...

Lisle 12340 Line Socket, 22mm Lisle 12340 Line Socket, 22mm Lisle 12340 Line Socket, 22mm

12050. SMALL MASTER CHUCK KEY. Has 4 sizes. Strong neodymium magnets for attachment close to the worksite or toolbox. Cast from alloy steel for str...

Use with a Breaker Bar to Loosen Stubborn Oxygen Sensors. Tool comes with both 1/2” and 3/8” drive. Attach a 1/2” breakerbar on the end of the tool...

Lisle 12320 Line Sockets, 19mm & 22mm Lisle 12320 Line Sockets, 19mm & 22mm Lisle 12320 Line Sockets, 19mm & 22mm

Designed for Easy Access on NOx and Soot Sensors. Includes 24mm & 30mm offset sockets with 1/2" drive. Each socket has 6 and 12 point options. ...

12220. NOX SENSOR THREAD CHASER M20. Cleans Threads in NOx Sensor Holes. Use with 13/16" hex socket or 3/8" square drive to restore M20x1.5 NOx sen...

12060. LARGE MASTER CHUCK KEY. Has 4 sizes. Strong neodymium magnets for attachment close to the worksite or toolbox. Cast from alloy steel for str...

Cleans dirt and corrosion from battery terminals and cable clamps. The external brush cleans cable clamps and internal brush cleans terminal posts....

11450. REPLACEMENT BLADE for a 11420 Hose Cutter.

Cuts Flexible Hose up to 1 1/4". The Hose Cutter will cleanly cut heater hoses, fuel lines, and other types of flexible hose up to 1 1/4". The stai...

Fuel Rail Cap 2Cap Used to Block Off the Fuel Rail During Fuel Pressure Diagnostics. (Ford 6.7L 2011-2022, Cummins 5.9L 2003-2009, Duramax 6.6L 200...

10550. SET REPLACEMENT STONES for 10500 Brake Cylinder Hone.

For 1 1/2" to 3 1/8" Disc Brake Cylinders (38.1 to 79.3mm). Special abrasive pads polish the cylinder without cutting. Controlled pressure, three a...

10050. Brake Cylinder Hone STONE SET. Stone Set for 10000. 240 grit, 1-1/8" long stones.

The OTC UH15FP is a 1500 Lb Capacity Underhoist Auxiliary Stand with a foot pedal - used under hoist to provide partial support for positioning of ...

HOSE REMOVAL SET (6-PIECE). Consisting of six (6) hose removal tools which consists of three (3) 10", soft-handled tools and three (3) 15", soft-ha...

ROLLING HEAD PRY BAR 6" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as an...

BALL HONE, 1 INCH - 1”, 25mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine lifters,...

BALL HONE, 5/8 INCH - 5/8”, 16mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine lift...

STRAIGHT-BLADE HOSE CUTTER. Cuts rubber hoses ranging from 1/4" to 1-1/2". Simply place hose in tool and squeeze handle to cut. Replacement steel c...

HOLE PUNCH KIT - Easy, smooth operation. Will pierce up to 14 gauge steel. 7 sets punches and dies. Sizes: 3/32", 1/8", 5/32", 3/16", 7/32", 1/4", ...

SEAL REPAIR KIT

DRIVER NO. 9

Makes it Easier to Insert Bearing Race. Insert bearing race quickly, straight in on FIRST TRY! Helps reduce damage to both race and axle housing. S...

Double Ended Tool for Removing and Installing Brake Springs. Use plier tips to stretch brake spring. Handle ends remove and install spring over anc...

A Special Tool for a Special Job. Coil Spring cutters polish the battery contact while stainless steel brushes clean the cable terminals.

PICK/HOOK & HOSE REMOVAL SET - Ergonomic handle design fits properly in the hand, allowing for easier holding of the tool. Hose removal tools c...

ROLLING HEAD PRY BAR 16" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as a...

BALL HONE SET (10 PIECE) - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine lifters, and u-joint y...

GM HEATER LINE QUICK-CONNECT RELEASE TOOL Specially designed for separating quick-connect fittings on heater lines of 1999-2004 Chevy and GMC C/K t...

SPECTRUM 30+4 30 PC. LED WORK LIGHT WITH 4 PC. LED TOP LIGHT. AN INFINITE SPECTRUM OF POSSIBILITIES. Combining a trouble light with a flashlight. C...

For removal & installation of ball joints, U-joints, wheel studs and more. Removal applications: , Buick RoadMaster, Cadillac XLR; XLR-V, Chevr...

1 In Collet & Pin Assembly for OTC TOOL 4581.

PROFESSIONAL STYLE SEAL PULLER - Designed to remove oil and grease seals when servicing cars, SUVs and light trucks without damaging the housing or...

REPLACEMENT SCREW PLUG