Tools > Pneumatic Fittings, Connectors & Accessories

WORM GEAR LINED 65E - Lined clamps are designed for use with silicone rubber and other soft hose applications. The liner protects the hose surface ...

WORM GEAR MICRO-GEAR® 62M - Micro-Gear 62M clamps are tiny, tough and precision engineered for use in small hose applications. Their slim 5/16″ ban...

Flex-Gear clamps use a Belleville spring design to eliminate "cold flow" leakage that adjusts with the hose and fitting to maintain constant tensio...

SPRING CLAMPS SMARTSEAL® 37215 - SmartSeal provides spring compensation over 360 degrees. That’s right, a self-adjusting all stainless steel clamp ...

1/4" FNPT straight through plugs are made of case hardened steel and are plated to resist rust. Designed for use with high pressure washers and ind...

1/4" FNPT swivel hose ends help eliminate kinked and twisted air lines. Full 360 degree swivel hose ends are made of steel construction and have a ...

Brass hose ferrules are made to create custom hose assemblies. These ferrules have a 5/8" OD and a 0.625 ID. Note that rubber hose tolerances vary ...

Milton AA style plugs are made of case hardened steel and are plated to resist rust. Featuring a push type sleeve, this 3/8" FNPT AA style coupler ...

Brass hose ferrules are made to create custom hose assemblies. These ferrules have a 3/4" OD and a 0.750 ID. Note that rubber hose tolerances vary ...

1/4" FNPT high flow V style plugs are used in applications that require high volume, low pressure. V style plugs offer a maximum of 300 PSI and a 1...

1/2" MNPT G style plugs are made of case hardened steel and are plated to resist rust. Milton G style couplers and plugs offer 1/2" basic flow size...

Avoid Lost Sales With A Wide Variety Of 90 Degree Elbows And Straight Hoses, In Both Single And Dual Id. Connectors And E-Z Coil Complete The Packa...

These Nylon Fittings Are Used To Connect Fuel Lines, Vacuum Hoses, Windshield Wiper And Emission Control Hoses. -50°F To 275°F (-46°C To 135°C). Re...

For Applications Where A Molded Hose Is Not Available, It Has A Corrugated Cover And A Wire Insert That Easily Bend To Replicate The Original Equip...

Designed To Transfer Glycol-Based Coolant Throughout The Vehicle'S Cooling System. The Epdm Tube And Cover And The Synthetic Reinforcement Meets Or...

A general purpose cooling system connector designed for heater and radiator hose applications. Constructed of glass-filled black nylon Kit includes...

Avoid Lost Sales With A Wide Variety Of 90 Degree Elbows And Straight Hoses, In Both Single And Dual Id. Connectors And E-Z Coil Complete The Packa...

These Nylon Fittings Are Used To Connect Fuel Lines, Vacuum Hoses, Windshield Wiper And Emission Control Hoses. -50°F To 275°F (-46°C To 135°C). St...

Designed To Transfer Glycol-Based Coolant Throughout The Vehicle'S Cooling System. The Epdm Tube And Cover And The Synthetic Reinforcement Meets Or...

JIC 37° Female Swivel. Easy to assemble, just push fitting into the hose. | Low cost and a wide selection of configurations and sizes. | Often used...

Female Pipe (NPTF). Easy to assemble, just push fitting into the hose and clamp. | Low cost and a good selection of sizes. | FS-500 label set will ...

Inverted Male Swivel. No clamps needed. | Easy to assemble, just push fitting into the hose. | Often used for low pressure lube and oil lines. | Lo...