Specialty Service Tools

SEAL REPAIR KIT

BALL HONE, 1 INCH - 1”, 25mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine lifters,...

HOSE REMOVAL TOOL - Unique tip easily fits between hose and fitting to break stubborn hoses loose. Large handle provides a reliable grip on tool du...

2-Stone Hone Fits Cylinders 11/16" to 2 1/2" (17.4 - 63.5mm). Controlled pressure makes it possible to polish or hone with just one stone grit. Squ...

DRIVER NO. 9

REPLACEMENT DRIVE SCREW

For 1 1/2" to 3 1/8" Disc Brake Cylinders (38.1 to 79.3mm). Special abrasive pads polish the cylinder without cutting. Controlled pressure, three a...

BALL HONE, 1 3/4 INCH - 1-3/4”, 44mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine ...

Designed for Easy Access on NOx and Soot Sensors. Includes 24mm & 30mm offset sockets with 1/2" drive. Each socket has 6 and 12 point options. ...

BALL HONE, 1 1/4 INCH - 1-1/4”, 32mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine ...

Replacement Chain. For OTC 6969 24" Ratcheting Chain Wrench

ROLLING HEAD PRY BAR 12" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as a...

10050. Brake Cylinder Hone STONE SET. Stone Set for 10000. 240 grit, 1-1/8" long stones.

Cleans Threads in Oxygen Sensor Holes. Use with 3/4" hex socket or 3/8" square drive. Size: M18x1.5 Also works on M18x1.5 spark plug threads. IMPOR...

Double Ended Tool for Removing and Installing Brake Springs. Use plier tips to stretch brake spring. Handle ends remove and install spring over anc...

Removes and Installs Oxygen Sensors on Most Domestic and Some Imports. Special 7/8" socket with cutaway slot to provide clearance for wire harness....

12050. SMALL MASTER CHUCK KEY. Has 4 sizes. Strong neodymium magnets for attachment close to the worksite or toolbox. Cast from alloy steel for str...

A Special Tool for a Special Job. Coil Spring cutters polish the battery contact while stainless steel brushes clean the cable terminals.

For Reinstalling the Manifold on Small Block Chevrolets. A simple way to expand a warped manifold so all bolt holes are accurately aligned. Helps p...

Cuts Flexible Hose up to 1 1/4". The Hose Cutter will cleanly cut heater hoses, fuel lines, and other types of flexible hose up to 1 1/4". The stai...

3-Stone Hone Fits Cylinders 27/32" to 2" (21.4-50.8mm). Controlled pressure makes it possible to polish or hone with just one stone grit. Square en...

REPLACEMENT SCREW PLUG

Use with a Breaker Bar to Loosen Stubborn Oxygen Sensors. Tool comes with both 1/2” and 3/8” drive. Attach a 1/2” breakerbar on the end of the tool...

12220. NOX SENSOR THREAD CHASER M20. Cleans Threads in NOx Sensor Holes. Use with 13/16" hex socket or 3/8" square drive to restore M20x1.5 NOx sen...

12060. LARGE MASTER CHUCK KEY. Has 4 sizes. Strong neodymium magnets for attachment close to the worksite or toolbox. Cast from alloy steel for str...

Makes it Easier to Insert Bearing Race. Insert bearing race quickly, straight in on FIRST TRY! Helps reduce damage to both race and axle housing. S...

12320. LINE SOCKETS, 19MM & 22MM. Designed to Replace Fuel Line Fittings on Cummins ISB and ISX engines. The sockets reduce the possibility of ...

Makes it Easier to Insert Wheel Bearing Race and Seals Without Damage to Race and Axle Housing. This master set includes nine drivers to fit most c...

GM HEATER LINE QUICK-CONNECT RELEASE TOOL Specially designed for separating quick-connect fittings on heater lines of 1999-2004 Chevy and GMC C/K t...

ROLLING HEAD PRY BAR 18" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as a...

ROLLING HEAD PRY BAR 6" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as an...

ROLLING HEAD PRY BAR 16" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as a...

FLEXIBLE HOSE CLAMP PLIERS - Allows technician to access the flat-type hose clamps located in hard-to-reach areas. Pliers has locking mechanism to ...

STRAIGHT-BLADE HOSE CUTTER. Cuts rubber hoses ranging from 1/4" to 1-1/2". Simply place hose in tool and squeeze handle to cut. Replacement steel c...

JIMMY BAR - 5/8" round, 18" long.

The OTC UH15FP is a 1500 Lb Capacity Underhoist Auxiliary Stand with a foot pedal - used under hoist to provide partial support for positioning of ...

HOSE REMOVAL SET (6-PIECE). Consisting of six (6) hose removal tools which consists of three (3) 10", soft-handled tools and three (3) 15", soft-ha...

BALL HONE, 1 1/2 INCH - 1-1/2”, 38mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine ...

MINI PICK & HOOK SET - 4 PIECE - Sturdy stainless steel points and shafts designed for marking, removing o-rings, accessing snap rings, and per...

BALL HONE, 3/4 INCH - 3/4”, 19mm Ball Hone - Ball Hones can be used for refinishing and resizing bores such as found in brake calipers, engine lift...

Fuel Rail Cap 2Cap Used to Block Off the Fuel Rail During Fuel Pressure Diagnostics. (Ford 6.7L 2011-2022, Cummins 5.9L 2003-2009, Duramax 6.6L 200...

PROFESSIONAL STYLE SEAL PULLER - Designed to remove oil and grease seals when servicing cars, SUVs and light trucks without damaging the housing or...

Injector Rail Fuel Line Cap Set, 5 pc.Caps Used to Block Off the Fuel Rail During Fuel Pressure Diagnostics in 2003-2022 Cummins, 2001-2022 Duramax...

O-RING / OIL SEAL PICK - For removing stubborn o-ring or oil seal out of its seat.

PICK/HOOK & HOSE REMOVAL SET - Ergonomic handle design fits properly in the hand, allowing for easier holding of the tool. Hose removal tools c...

ROLLING HEAD PRY BAR 16" LONG - You'll have a lot of leverage using one of these rolling head pry bars. The long, tapered body will also serve as a...